HU | EN

VEKOP-2.1.1-15 Vállalatok K+F+I tevékenységének támogatása

SAFETY RULES

To minimise accidents due to unsafe abrasives only use products bearing the oSa® logo

Never - Always

 

Always

Never

Permit untrained people to handle, store, mount or use abrasives
Observe the safety recommendations of the machine and wheel manufacturer
Mount or remove a wheel until the machine has been isolated from its power source
Keep the working area well lit, clean, tidy and free from obstructions
Mount a wheel that cannot be identified or one which does not bear the correct marking
Avoid slippery and uneven floors and do not work on ice or snow
Mount a wheel on a machine which does not display its spindle speed
Ensure other workers in the vicinity and passers-by are protected from sparks and debris
Mount a wheel which is beyond its marked expiry date or recommended shelf life
Exercise care when handling abrasive wheels – they can easily be damaged
Mount a wheel that has been dropped, damaged or incorrectly stored
Store wheels in dry and frost-free conditions avoiding wide variations in temperature and the risk of damage
Apply force to fit the wheel on the mounting device or alter the bore size or allow the wheel to overheat
Visually check the wheel for damage or defects and conduct a ring test before mounting
Tighten flanges with excessive force or use a hammer or extension
Check that the wheel is the correct specification for the application and that the markings are intact and legible
Use damaged, distorted or dirty flanges and fastening screws
Use the correct tools when mounting or removing a wheel
Use a machine which is not in good condition or one with a damaged guard
Ensure mounting flanges are in matched pairs, clean, free from burrs and undistorted
Turn on the machine until the wheel guard has been re-fitted, secured and adjusted correctly
Use blotters to prevent wheel slippage where required
Stand in the line of the grinding wheel when starting the motor after fitting or re-fitting a wheel
Make sure that workrests and workpiece clamping devices are secure and correctly positioned
Start the wheel in contact with the workpiece or any other object
Ensure guards are in position and correctly adjusted so that they do not foul the wheel
Mount a wheel on a machine running at a speed higher than the maximum operating speed marked on the wheel
Rotate the wheel manually to ensure that it runs true and freely before turning on the power
Work from a ladder or in a position where you do not have full control of the machine
Wear suitable protective clothing
Impact the work onto the wheel or the wheel onto the work
Run the wheel for at least 30 seconds at operating speed after mounting or re-mounting. Stand out of the line of the wheel when turning on the machine
Grind on the side of a wheel unless it is specially designed for this application
Dress bench grinding wheels regularly to keep the cutting surface in good condition
Apply side pressure by trying to cut curves or by grinding surfaces with cutting-off wheels
Allow the wheel to come to rest naturally after turning off the machine
Allow the wheel to bounce or be trapped or pinched in the cut
Ensure the workpiece is properly supported or clamped so that it cannot move during grinding or cutting
Use type 27 depressed centre grinding wheels at a steep angle or try to cut with them
Spin out residual coolant from the wheel before turning off the machine
Dress the wheel with any device other than that recommended
Report wheel breakages, keeping hold of all of the debris for examination
Press against the wheel surface to stop it or put down a machine until the wheel has stopped running
Ensure machine spindle speed is checked periodically using a tachometer
Wear the wheel down to the mounting flanges
Ensure that damaged or defective wheels and worn-out wheels are destroyed to prevent them from being used
Allow the gap between the wheel and workrest to exceed 3 mm
Ensure that the wheel is removed before transporting or storing portable machines
Allow coolant to run on a stationary wheel or leave the wheel running on an unattended machine
 

 


 

Miért a GRANITot válassza?

Magas minőség

Minőségi alapanyagok felhasználásával, korszerű technológiával, szigorú minőségellenőrzési és biztonsági előírásoknak megfelelően gyártjuk termékeinket.

Kedvező ár

A professzionális minőségű és kedvező árú Granit termékekkel partnereink az optimális ár-érték arányú megoldást választják.

Raktárról

A katalógusban szereplő Granit termékek jelentős része raktárról azonnal elérhető. A speciális, rendelésre gyártott termékek szállítási határideje rövid.

Megoldás egyedi igényekre

Készen állunk egyedi igények kielégítésére, szakembereink megoldásokat kínálnak, termékösszetételeket ajánlanak és új termékeket fejlesztenek konkrét köszörülési feladatokra.

Kapcsolatfelvétel

Budapest HUNGARY
Fadrusz J. u. 2.
H-1194

+ 36 1 347-9830
ertekesites@granitabrasive.com
www.granitabrasive.hu

Mintabolt nyitvatartás:
H-P: 7:30-13:00

Beérkező áruk lerakása:
H-CS: 7:30-15:30
P: 7:30-13:30

A * jelölt rész kitöltése kötelező